Wascomat EX618 Service Manual Download Page 126 | Manualshive

Page: 126 / 142

background image

126

Troubleshooting

Error codes from MCU

Error code 31, HEAT SINK TOO HOT

This error code is generated by the motor control. There is a temperature
sensor (NTC) mounted on the motor control cooling flange next to the po-
wer transistors in the output stage. If the temperature of the cooling flange
gets too high (> 90°C) the error code will be set to protect the transistors.
The cause of high cooling flange temperature can be e.g. a stiff drum in
combination with intensive use and high ambient temperature. There may
also be an error in the motor (sticking bearings or short circuit in windings,
which impairs the efficiency of the motor).
Actions:

•  Make sure the drum turns easily.
•  Check the value on the error code counter for error code 31.
•  Check the last 8 motor control error codes.
•  Start a 90°C normal program with load on continuous operation and

measure the temperature of the motor and motor control.

• Replace the defective part.

«
...
124
125
126
127
128
...
»

Summary of Contents for EX618















































































































































Reviews:

No comments

Related manuals for EX618

Brand: Haier Pages: 12

Brand: Indesit Pages: 72

Brand: Baumatic Pages: 33

Brand: Hotpoint Ariston Pages: 76

Aquarius WDF 756 A

Brand: Hotpoint Pages: 16

Brand: UNITED Pages: 80

Brand: Kärcher Pages: 15

Brand: HERKULES Pages: 20

Brand: Monogram Pages: 88

Brand: Hanseatic Pages: 78

Brand: Kärcher Pages: 20

Brand: Leonard Pages: 497

Brand: Westinghouse Pages: 78

Brand: Kärcher Pages: 276

WF45N6300A Series

Brand: Samsung Pages: 58

Brand: Samsung Pages: 68

Brand: Samsung Pages: 124

Brand: Samsung Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands