Wascomat EX618 Service Manual Download Page 2 | Manualshive

Page: 2 / 142

background image

Before ordering parts, refer to the Wascomat spare parts
manual (also available on www.wascomat.com) to
determine the part number(s) for the item(s) you need.

For quick service, please have the following information
available:
1.  Part Number of the item(s) you need.
2.  Model of the machine.
3.  Serial number of the machine.
4.  Electrical data for the machine:

– 120 or 208-240 Volt?

– Single or three phase?

– 50 or 60 Cycle?

To insure parts order accuracy, only fax or email
parts orders are accepted:

– Fax: 516-371-4029

– email: [email protected]

For service information, first contact your local authorized
Wascomat dealer.

Wascomat technical support can assist you or your
technician to diagnose and repair your laundry machines
over the phone. Please call from the location where the
machines are installed (we suggest you use a cellular or
cordless phone), and have the following information
available:
1.  Model of the machine.
2.  Serial number of the machine.
3.  Electrical data for the machine:

– 120 or 208-240 Volt?

– Single or three phase?

– 50 or 60 Cycle?

4. An accurate description of the malfunction.

Wascomat customer support

Whether you need spare parts or technical advice to guide you to the source of a

malfunction, our nationwide network of authorized dealers are able and ready to serve

your needs, or call the Wascomat customer Service Hotlines listed below.

For PArTS, SErViCE ANd TEChNiCAl ASSiSTANCE CAll your loCAl WASCoMAT dEAlEr

spare parts

technical support

Warranty claims

Wascomat’s Technical Support staff will honor valid manufacturer’s parts warranty claims providing your Wascomat

machines are registered for warranty coverage upon installation. if they are not registered, you can validate your

warranty claim by providing information about when and where you purchased the Wascomat machine(s), the model and

serial number(s). additional warranty proof may also be required.

461 Doughty Blvd., inwood, n.Y. 11096-0338

|

Sales and administration – Tel: 516-371-4400

•

Fax: 516-371-4204

•

e-mail: [email protected]

Spare Parts – Tel: 516-371-2000

•

Fax: 516-371-4029

•

e-mail: [email protected]

|

Technical Support – Tel: 516-371-0700

•

Fax: 516-371-4029

en Mexico: llame gratis a este numero 001-800-010-1010

516-371-2000

516-371-0700

To expedite parts order shipment, please use your credit card.

We accept: american express, Mastercard, visa, Discover, Diner’s club.

«
1
2
3
4
...
»

Summary of Contents for EX618















































































































































Reviews:

No comments

Related manuals for EX618

Washing Machine

Brand: BALAY Pages: 8

Brand: Jenn-Air Pages: 40

Brand: Jenn-Air Pages: 3

Brand: Rac Pages: 5

Brand: Smeg Pages: 29

Brand: ECG Pages: 188

Brand: Hotpoint Pages: 48

Brand: Siebring Pages: 40

Brand: Scandium Pages: 40

Brand: Speed Queen Pages: 1

Brand: Walter Pages: 136

Brand: ZANKER Pages: 24

Brand: Indesit Pages: 16

Brand: Klarstein Pages: 168

Brand: ROBINHOOD Pages: 15

Brand: Monogram Pages: 32

Brand: Troy-Bilt Pages: 60

Brand: Ardo Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands