Wascomat EX618 Service Manual Download Page 59 | Manualshive

Page: 59 / 142

background image

59

QUICK START BUTTON 1

and 2 (COIN)

Select if the two buttons, available on the Compass timer, shall be used as
quick start buttons or as option buttons.

Yes =

The button is set to quick start.

No =

The button is set to option button.

NOTE!

Only in GEN6COINOP software and Freescale microprocessor S12.

VOLUME

Set the volume on the voice guidance board (if the machine is equipped
with voice guidance).
A value between 0 and 255 can be used where 0 will turn the voice gui-
dance off

VGB. WELC. TIMEOUT SEC.

Select if a welcome message will be sent out from the voice guidance or
not. If timeout gone and machine not operating, a welcome message will
be sent out from the voice guidance if door opened/closed, any buttons
pressed or program selector used.
If timeout not gone, welcome message will be omitted.

VGB. MESS. ANTICR. SEC.

Select if anticrease message shall be sent out or not by the voice guidance
system after drying. The anticrease function will make the drum moving
backwards and forwards a certain time after the drying cycle has ended.
When the machine enter anticrease after drying, a message will always be
sent out that door can not be unlocked if program selector is pressed. This
message will be repeated with a frequency defined by the time set in this
menu. 0 = no message will be sent out.

Program unit

«
...
57
58
59
60
61
...
»

Summary of Contents for EX618















































































































































Reviews:

No comments

Related manuals for EX618

Brand: Haier Pages: 10

Brand: Haier Pages: 10

Brand: Haier Pages: 18

Brand: Haier Pages: 18

Brand: Haier Pages: 18

Brand: Haier Pages: 40

Brand: Haier Pages: 15

Brand: Haier Pages: 8

Brand: Haier Pages: 18

Brand: Haier Pages: 20

Brand: Haier Pages: 10

HW-C1470TVE ME-U

Brand: Haier Pages: 19

Brand: Haier Pages: 20

Brand: Haier Pages: 20

Brand: Haier Pages: 19

Brand: Haier Pages: 16

Brand: Haier Pages: 18

Brand: Haier Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands