Wascomat EX618 Service Manual Download Page 46

Page: 46 / 142

6204

CONFIG 1

04.01.00.00

PAUSE PERMITTED

RAPID ADVANCE

NEW PROG. SELECT

SHOW TIME

SHOW TEMP

CONFIG 1

04.01.00.00

PAUSE PERMITTED

YES

CONFIG 1

04.34.00.00

MAX FILLTIME, SEC

0600

SAVE TO MEMORY

YES

Program unit

Select the desired function/parameter and press
the knob.
To engage and disengage functions, turn the

knob to select YES or NO and then press the

knob.
To adjust the value, set the value and press the
knob. The arrow in each menu shows the co-
lumn to be adjusted.

• Turn the knob clockwise to set the desired

number between 0 and 9.

• Turn the knob anticlockwise to move to the

next column. Turn the knob clockwise and set
the value, etc.

• Once all the columns have been set, press

the knob to confirm and go back to the config
menu 1.

When all the relevant values have been adjusted,
select

EXIT

and press the knob.

Confirm the changes (write to memory YES/NO)

and return to the main menu.

Note!

All changes will be executed only after exiting

the CONFIG 1 menu.

Summary of Contents for EX618















































































































































Search results

Summary of Contents for EX618

Reviews:

Related manuals for EX618

Brands by name

Popular brands

Wascomat EX618, Service Manual

Search results

Summary of Contents for EX618

Reviews:

Related manuals for EX618

Brands by name

Popular brands