Wascomat EX618 Service Manual Download Page 90 | Manualshive

Page: 90 / 142

background image

90

Motor and motor control

LED indications

Two LEDs, one yellow and one green, indicate status and any errors on the
motor controller and motor.
The table below shows the blinking patterns of the various error codes.

Green LED

LED blinking pattern

Cause

OK blink (brief pause every 5 seconds)

Microcomputor in motor control unit not working, voltage is on.

Current limiter of motor control has switched on.

Yellow LED

LED blinking pattern

Error code on display

Cause

31E

HEATSINK TOO HOT

Overheated heat sink on motor control.

32E

MOTOR TOO HOT

Motor thermal protector has triggered.

33E

NO INTERLOCK

Motor controller receives start request,

but receives no lock ACK (input 302).

13E

NO MOTOR COMM.

Communication error motor control -

programme unit.

-

-

Short-circuit in motor winding, harness

or internally in motor control.

Motor control restarts automatically.

35E

MOTOR SHORTNING

Short-circuit in motor winding, harness

or internally in motor control.

36E

INTERLOCK HARDWARE Error in lock ACK circuits in motor

controller.

37E

LOW DC VOLTAGE

DC level in motor control too low.

38E

HIGH DC VOLTAGE

DC level in motor control too high.

45E

MOTOR NOT FOLLOW

No tacho signal, the motor is not turning

over.

approx. 5 seconds

approx. 5 seconds

7

7

«
...
88
89
90
91
92
...
»

Summary of Contents for EX618















































































































































Reviews:

No comments

Related manuals for EX618

Brand: Jackson Pages: 2

Brand: Maytag Pages: 88

Brand: Maytag Pages: 48

Brand: Akai Pages: 28

HDS 2.3/12 C Ed

Brand: Kärcher Pages: 48

Brand: Omega Pages: 32

Brand: Kärcher Pages: 168

Brand: GE Pages: 40

HD 4.5/32-4 S Eb HD 4.5/32-4 S Ec

Brand: Kärcher Pages: 44

Brand: Simpson Pages: 28

Brand: Ariston Pages: 60

Brand: Bartscher Pages: 32

Brand: Samsung Pages: 73

Brand: Samsung Pages: 76

Brand: Samsung Pages: 76

WF365BTB series

Brand: Samsung Pages: 43

Brand: Samsung Pages: 208

Brand: Samsung Pages: 132

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands