Wascomat EX618 Service Manual Download Page 119 | Manualshive

Page: 119 / 142

background image

119

Troubleshooting

Error code 07, OVERFILLED

This error code is generated by the CPU board. The error code arises if
the drum has been filled with water above a predetermined level during an
on-going wash program. It can be caused by a blocked level hose, drops
of water in the level tube, defective filler valve, defective electronic filler
control, etc.
Action:

• Blow through the level hose and check that it is not blocked and does

not contain any water.

• Check in the service program that the level control is working correctly.
• Check using the service program that all the water valves are working

correctly.

Error code 08, NO HEATING

This error code is generated by the CPU board. The error code means that
the temperature is rising too slowly when heating is active. The limit for this
error code is normally set to a water temperature increase of approx. 3°C
per 10 minutes but can vary depending on the type of machine and the
software.
The error code can be caused by a defective heater element, a break in
the power supply to the heater element, defective heater contactor, etc.
On machines built for washing mops, it can be caused by too low a level in
the program stage. The lowest level for a mop program in the main wash
with heating is 90 scale units.

«
...
117
118
119
120
121
...
»

Summary of Contents for EX618















































































































































Reviews:

No comments

Related manuals for EX618

Brand: GE Pages: 24

Brand: GE Pages: 2

DW60M6050 Series

Brand: Samsung Pages: 112

Brand: DAEWOO ELECTRONICS Pages: 28

Brand: Hyundai power products Pages: 36

NAGOLD SERENE FI02

Brand: Hafele Pages: 59

Brand: Asko Pages: 16

Brand: Alliance Laundry Systems Pages: 38

Brand: GE Pages: 72

Brand: Winterhalter Pages: 11

Brand: V-TUF Pages: 15

Brand: Kärcher Pages: 24

Brand: Parmco Pages: 22

Brand: Maytag Pages: 56

Brand: Feider Machines Pages: 26

Brand: Listo Pages: 176

Brand: Heinner Pages: 59

Brand: Kruger Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands