WAGO I/O-SYSTEM 750-666/000-003 Manual Download Page 131

Page: 131 / 166

WAGO-I/O-SYSTEM 750

Diagnostics 131

750-666/000-003 4FDI/2FDO 24V/10A PROFIsafe V2 iPar

Manual

Version 1.2.0, valid from HW/SW Version 01/01

Table 41: Diagnostic messages

Alarm

Description

Invalid
F_WD_Time

Diagnostic
type

Module Diagnostics

Coding:

0x0043

LED
indication

Group error (E) red
PROFIsafe (G) red

Solution

The monitoring time for the fail-safe data
exchange must be set to a value greater
than 0 ms. Correct the F parameterization.

Undervoltage

Diagnostic
type

Module Diagnostics

Coding:

0x0202

LED
indication

Group error (E) red

Solution

The 24V field supply of the F I/O module
is below the specified tolerance. Correct
the voltage supply responsible.

Undervoltage PWR

Diagnostic
type

Module Diagnostics

Coding:

0x0220

LED
indication

Group error (E) red

Solution

The 24V power supply of the F I/O module
is below the specified tolerance. Correct
the voltage supply responsible. Check for
short circuit.

Wiring error

Diagnostic
type

Channel Diagnostics

Coding:

0x021D

LED
indication

Status On (I or K) red,
group error (E) red

Solution

The wiring of output O2 does not
correspond to the selected output
configuration. Correct either the output
configuration or the wiring.

Summary of Contents for I/O-SYSTEM 750-666/000-003







































































































































































Search results

Summary of Contents for I/O-SYSTEM 750-666/000-003

Reviews:

Brands by name

Popular brands

WAGO I/O-SYSTEM 750-666/000-003, Manual

Search results

Summary of Contents for I/O-SYSTEM 750-666/000-003

Reviews:

Brands by name

Popular brands