WAGO 750-494 Series Manual Download Page 19

Page: 19 / 134

WAGO-I/O-SYSTEM 750

Device Description

750-494 3-Phase Power Measurement Module

Manual

Version 1.2.0

Pos: 38 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 2/Anzeig eel emente - Ü berschrift 2 @ 4\mod_1240984390875_21.docx @ 31964 @ 2 @ 1

3.3

Display Elements

Pos: 39 /Serie 750 ( WAGO-I/O-SYST EM)/Ger ätebeschrei bung/Anzeigeelemente/Anal ogei ngangsklemmen/Anzeigeel emente 750- 0494, - 0495 @ 16\mod_1371738731125_21.docx @ 123880 @ @ 1

LED A indicates the operating status, LEDs B … H indicate possible errors.

Figure 4: Display Elements

The meaning of these indications is as follows:

Table 7: Legend for Figure “Display Elements”

LED

State

Message

Off

No operational readiness or

the internal data bus communication is interrupted.

Note: If the watchdog was disabled, the LED is always

green. See section “Commissioning” > “Configuration

with WAGO-I/O-

CHECK

“.

Green Operational readiness and correct internal data bus

communication

Off No error

Red General error message for L1:

Under-/overvoltage or overcurrent

Off No error

Red General error message: Clipping of a current measuring

path IL1, IL2 or IL3

Off No error

Red High measuring error, caused by undershooting the min.

voltage at L1, L2 or L3

Off No error

Red General error message for L2:

Under-/overvoltage or overcurrent

Off No error

Red General error message for L3:

Under-/overvoltage or overcurrent

Off No error

Red General error message: Clipping of a voltage measuring

path L1, L2 or L3

Off No error

Yellow Error of the phase sequence L1-L2-L3

Pos: 40 /D okumentation allgemei n/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Summary of Contents for 750-494 Series







































































































































Search results

Summary of Contents for 750-494 Series

Reviews:

Related manuals for 750-494 Series

Brands by name

Popular brands

WAGO 750-494 Series, Manual

Search results

Summary of Contents for 750-494 Series

Reviews:

Related manuals for 750-494 Series

Brands by name

Popular brands