WAGO 750-494 Series Manual Download Page 32

Page: 32 / 134

Function Description

WAGO-I/O-SYSTEM 750

750-494 3-Phase Power Measurement Module

Manual

Version 1.2.0

Rotary field:

• Direction of rotation

Limit values:

• Undervoltage Lx

• Overvoltage Lx

• Overcurrent Lx

Harmonics!

In general, the first harmonic means the fundamental wave and the second

harmonic means the wave with double frequency etc.!

Alternatively, the following

DC measured values

are available if DC

measurement has been activated in the I/O module. See section "Commissioning"

> "Configuration with WAGO-I/O-

CHECK

DC measurements only possible in 2 measuring channels!

DC measurements are only possible in the measuring channels L1-IL1 and L2-

IL2!

Voltage:

• DC voltage

Lx-N

Current:

• DC current Lx

Power:

• Power (DC current) Lx

4.3

Description of Measured Values

Calculating the RMS Values for Current and Voltage

The I/O module measures the true RMS of the voltages and currents applied to

the measurement inputs per period. See figure below.

∑

N-1

eff

∑

N-1

eff

: Sampling value of current

eff

RMS value of the current

: Sampling value of voltage

eff

: RMS value of the voltage

Summary of Contents for 750-494 Series







































































































































Search results

Summary of Contents for 750-494 Series

Reviews:

Related manuals for 750-494 Series

Brands by name

Popular brands

WAGO 750-494 Series, Manual

Search results

Summary of Contents for 750-494 Series

Reviews:

Related manuals for 750-494 Series

Brands by name

Popular brands