WAGO 750-494 Series Manual Download Page 3

Page: 3 / 134

WAGO-I/O-SYSTEM 750

Table of Contents

750-494 3-Phase Power Measurement Module

Manual

Version 1.2.0

Pos: 5 /D okumentati on allgemein/Verzeichnisse/Inhaltsverzeichnis - Ü berschrift oG und Verzei chnis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1

Table of Contents

Notes about this Documentation ................................................................. 6

1.1

Validity of this Documentation ................................................................. 6

1.2

Revision History ........................................................................................ 7

1.3

1.4

Symbols ..................................................................................................... 8

1.5

Number Notation ..................................................................................... 10

1.6

Font Conventions .................................................................................... 10

Important Notes ......................................................................................... 11

2.1

Legal Bases ............................................................................................. 11

2.1.1

Subject to Changes ............................................................................. 11

2.1.2

Personnel Qualifications ..................................................................... 11

2.1.3

Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions ........................................................................ 11

2.1.4

Technical Condition of Specified Devices ......................................... 12

2.2

Safety Advice (Precautions) .................................................................... 13

Device Description ..................................................................................... 15

3.1

View ........................................................................................................ 16

3.2

Connectors ............................................................................................... 17

3.2.1

Data Contacts/Internal Bus ................................................................. 17

3.2.2

Power Jumper Contacts/Field Supply ................................................ 17

3.2.3

CAGE CLAMP

Connectors ............................................................. 18

3.3

Display Elements .................................................................................... 19

3.4

Operating Elements ................................................................................. 20

3.5

Schematic Diagram ................................................................................. 21

3.6

Technical Data ........................................................................................ 23

3.6.1

Dimensions and Weight ..................................................................... 23

3.6.2

Voltage Supply ................................................................................... 23

3.6.3

Measuring Inputs ................................................................................ 23

3.6.4

Measured Values ................................................................................ 24

3.6.5

Internal Bus Communication .............................................................. 25

3.6.6

Connection Type ................................................................................ 25

3.6.7

Climatic Environmental Conditions ................................................... 26

3.7

Approvals ................................................................................................ 27

3.8

Standards and Guidelines ........................................................................ 29

Function Description ................................................................................. 30

4.1

Measuring Principle ................................................................................ 30

4.2

Measured Values ..................................................................................... 30

4.3

Description of Measured Values ............................................................. 32

4.4

Measuring Errors and Accuracy .............................................................. 38

Process Image ............................................................................................. 40

5.1

Overview of Process Data ....................................................................... 40

5.2

Output Data ............................................................................................. 41

5.2.1

Definition of Control Words .............................................................. 41

5.2.2

Definition of Output Data Words ....................................................... 42

5.3

Input Data ................................................................................................ 43

Summary of Contents for 750-494 Series







































































































































Search results

Summary of Contents for 750-494 Series

Reviews:

Related manuals for 750-494 Series

Brands by name

Popular brands

WAGO 750-494 Series, Manual

Search results

Summary of Contents for 750-494 Series

Reviews:

Related manuals for 750-494 Series

Brands by name

Popular brands