WAGO 750-494 Series Manual Download Page 7

Page: 7 / 134

WAGO-I/O-SYSTEM 750

Notes about this Documentation

750-494 3-Phase Power Measurement Module

Manual

Version 1.2.0

Pos: 15 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 2/Änderungshistori e - Ü berschrift 2 @ 6\mod_1255513312687_21.docx @ 42790 @ 2 @ 1

1.2

Revision History

Pos: 16 /Serie 750 ( WAGO-I/O-SYST EM)/Hi nweise zur D okumentati on/Änderungshistori e/Buskl emmen/Änderungshistori e -494 @ 14\mod_1363950530870_21.docx @ 115624 @ @ 1

Table 2: Revision History

Document

Version

Device Version

Description of Change

Hardware Software

1.0.0

First issue

1.0.1

In section „Commissioning“ >

„Displaying the Measured Values via

WAGO-I/O-

CHECK

“ the figure

„Measured values, harmonics chart“ was

changed.

1.1.0

Change of approvals

1.2.0

Change of approvals

Pos: 17.1 /All e Seri en ( Allgemei ne Module)/Ü berschriften/Ebene 2/Ur heberschutz - Ü berschrift 2 @ 23\mod_1435647042188_21.docx @ 184808 @ 2 @ 1

1.3

Copyright

Pos: 17.2 /All e Seri en ( Allgemei ne Module)/R echtliches, Allgemei nes/Urheberschutz ausführlich @ 4\mod_1235565145234_21.docx @ 27691 @ @ 1

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 17.3 /Dokumentation allgemei n/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Summary of Contents for 750-494 Series







































































































































Search results

Summary of Contents for 750-494 Series

Reviews:

Related manuals for 750-494 Series

Brands by name

Popular brands

WAGO 750-494 Series, Manual

Search results

Summary of Contents for 750-494 Series

Reviews:

Related manuals for 750-494 Series

Brands by name

Popular brands