WAGO 750-494 Series Manual Download Page 79

Page: 79 / 134

WAGO-I/O-SYSTEM 750

Commissioning

750-494 3-Phase Power Measurement Module

Manual

Version 1.2.0

Pos: 95 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/In Betri eb nehmen - Ü berschrift 1 @ 4\mod_1240901452750_21.docx @ 31570 @ 1 @ 1

Commissioning

Pos: 96 /Serie 750 ( WAGO-I/O-SYST EM)/In Betrieb nehmen/Parametrier en mit WAGO- I/O-CH ECK/Parametrier en mit WAGO-I/O-CH ECK 750-0494 @ 15\mod_1367496874664_21.docx @ 118340 @ 233333 @ 1

The I/O module latched in the bus node and wired for the measurement can be put

into operation using the WAGO-I/O-

CHECK

software for Windows. For that, the

fieldbus coupler/controller of the node is connected, for example, to the USB port

of a PC using the WAGO USB communication cable.

WAGO-I/O-

CHECK

provides the following functions:

•

Graphic display of the bus node

•

Display, recording and export of the process data (measured values)

•

Application settings

•

Settings for the measurements for each of the three phases

•

I/O module settings

•

Settings for saving the energy values

•

Saving all settings

WAGO-I/O-

CHECK

You can obtain the WAGO-I/O-

CHECK

software on a CD under Item No. 759-

302. This CD contains all the application program files and a description.

The description is also available in the Internet at

http://www.wago.com

under

Documentation > WAGO Software > WAGO-I/O-

CHECK.

To display the bus node on the PC, use the USB communication cable to connect

coupler/controller and PC and launch WAGO-I/O-

CHECK.

Summary of Contents for 750-494 Series







































































































































Search results

Summary of Contents for 750-494 Series

Reviews:

Related manuals for 750-494 Series

Brands by name

Popular brands

WAGO 750-494 Series, Manual

Search results

Summary of Contents for 750-494 Series

Reviews:

Related manuals for 750-494 Series

Brands by name

Popular brands