Volvo D12 Operator'S Manual Download Page 36

Page: 36 / 214

Engine Storage

If the vehicle needs to be parked for a pe-
riod (more than 30 days), make sure to
protect it as follows:

Drain the engine of its used oil.

Fill up to the proper level with oil of
the recommended quality and viscos-
ity.

Fill up the fuel tanks with the recom-
mended grade of fuel.

Run the engine for two minutes around
1000 r/min. Shut the engine down. Do
not drain the oil after this run.

Check the engine air filter and, if nec-
essary, change it.

Check the coolant for proper levels of
antifreeze and inhibitor (SCA) protec-
tion. Service as necessary.

Clean the exterior of the engine.

Seal all engine openings using a wa-
terproof, vaporproof and strong tape.

To return an engine preserved in this man-
ner can be done in a short time by removing
the seals and checking all engine fluids:
coolant, fuel, crankcase oil. Also check all
other component fluid levels on the vehicle.

Summary of Contents for D12























































































































































































































Search results

Summary of Contents for D12

Reviews:

Related manuals for D12

Brands by name

Popular brands

Volvo D12, Operator'S Manual

Search results

Summary of Contents for D12

Reviews:

Related manuals for D12

Brands by name

Popular brands