Volvo D12 Operator'S Manual Download Page 3

Page: 3 / 214

Contents

General Information ............................. 1

Information For the Owner ................... 1

Safety Information ................................. 3

Proper Maintenance Procedure ............. 3

Injury Prevention ................................... 6

Engine Damage Prevention ................. 15

Electric System Damage Prevention .. 17

Reporting Safety Defects .................... 19

General Engine Design Information . 20

Engine Overview D7 ........................... 20

Engine Overview, D12 ........................ 22

Typical Engine Compartment
Overview ............................................. 24

Engine Features ................................... 26

VECTRO II Parameter Values, D7 .... 27

VECTRO II Parameter Values, D12 .. 28

Engine Variants, D7 ............................ 29

Engine Variants, D12 .......................... 30

Engine Data ......................................... 31

Engine Storage ..................................... 32

Engine Storage .................................... 32

Cooling System ..................................... 34

General Coolant Information .............. 34

Water Specification ............................. 40

Additives .............................................. 41

Antifreeze ............................................ 42

Fuel System .......................................... 50

Fuel Safety Reminders ........................ 50

Diesel Fuel Specification .................... 51

Fuel Additives ..................................... 55

Alternative Fuels ................................. 58

Oil System ............................................. 59

Engine Oil ........................................... 59

Oil Sampling ....................................... 70

Severe Service Schedule for
VHD-Series ........................................... 74

General and Check-Chart ................... 74

Maintenance Categories ...................... 78

Heavy-Duty Service Schedule for
VHD-Series ........................................... 84

General and Check-Chart ................... 84

Maintenance Categories ...................... 89

Maintenance ......................................... 95

Engine Maintenance ............................ 95

Flushing Cooling System, D7 .......... 121

Flushing Cooling System, D12 ........ 124

Turbo and Charge Air Cooler ........... 126

Replacing Fuel Filters ....................... 128

Fuel System Service ......................... 129

Transmission and Rear Axle Main-
tenance ............................................... 139

Steering and Brakes Maintenance .... 143
Electrical System Maintenance ......... 149

Tires, Wheels and Hub Maintenance

151

Chassis Maintenance ......................... 155

Cab Maintenance ............................... 157

Lubrication, VHD ............................. 162

Viscosity and Capacity Tables .......... 166

Literature ............................................ 172

Service Assistance and Manuals ...... 172

Service Charts .................................... 174

Scheduled Services ........................... 174

Repair Record ................................... 177

Tire Record ........................................ 183

Fuel and Oil Record ......................... 194

Index .................................................... 207

Summary of Contents for D12























































































































































































































Search results

Summary of Contents for D12

Reviews:

Related manuals for D12

Brands by name

Popular brands

Volvo D12, Operator'S Manual

Search results

Summary of Contents for D12

Reviews:

Related manuals for D12

Brands by name

Popular brands