Volvo D12 Operator'S Manual Download Page 87

Page: 87 / 214

Severe Service Schedule for VHD-Series

Category C:
Additional Service Points

Do the maintenance points as de-
scribed under Category a, A and B.

Change standard antifreeze every
4,000 hours. (See page 122 or page
124.)

Extended life antifreeze should have
an extender package added at 3,000
hours and then changed at 6,000
hours. (See page 122 or page 124.)

Check coolant thermostat function ev-
ery 2,000 hours.

Pressure test injectors or adjust height:

•

Volvo D7: Every 12 months or
2,000 hours.

•

Volvo D12: No recommendation.

•

Cummins: Every 21 months or
3,800 hours.

•

Detroit Diesel: Every 21 months
or 3,800 hours

Check and adjust valves on the engine:

•

Volvo: Every 12 months or 2,000
hours.

•

Cummins: Every 21 months or
3,800 hours.

•

Detroit Diesel: Every 21 months
or 3,800 hours.

Change power steering filter annually.
(See page 143.)

Summary of Contents for D12























































































































































































































Search results

Summary of Contents for D12

Reviews:

Related manuals for D12

Brands by name

Popular brands

Volvo D12, Operator'S Manual

Search results

Summary of Contents for D12

Reviews:

Related manuals for D12

Brands by name

Popular brands