Volvo D12 Operator'S Manual Download Page 121 | Manualshive

Page: 121 / 214

background image

Maintenance

117

Oil Filters

Before working on or inspecting a vehi-
cle, set the parking brakes, place the
transmission in neutral and block the
wheels. Failure to do so can result in un-
expected vehicle movement and can
cause serious personal injury or death.

WARNING

Hot oil can cause severe burns. Do not
allow hot oil to contact the skin. When
changing oil, wear protective gloves.

CAUTION

Use only the engine manufacturer’s oil
filter for replacement. Use of an oil filter
not built to specification could result in
severe damage to bearings, crankshaft,
etc. as a result of unfiltered oil entering
the lubrication system.

NOTE! Always dispose of oil filters ac-
cording to Federal or local regulations.
Used oil disposed of in nature or water-
ways contaminates our drinking water and
kills wildlife.

Install new filters as follows:

•

Coat the filter gasket with oil.

•

Install the filter and turn it by hand
until the gasket makes contact with the
sealing surface.

•

Then turn the filter an additional 3/4
turn.

W2003480

D12 Oil Filters

W2003078

D7 Oil Filters:

1

Full-flow Filter

2

Bypass Filter

«
...
119
120
121
122
123
...
»

Summary of Contents for D12























































































































































































































Reviews:

No comments

Related manuals for D12

Brand: Hägglunds Pages: 56

Brand: AL-KO Pages: 182

Brand: DR Pages: 20

Brand: Volkswagen Pages: 17

MaxxForce DT 10

Brand: Navistar Pages: 109

Brand: TOPMAQ Pages: 17

Brand: Perkins Pages: 27

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 16

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 13

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands