manualshive.com logo in svg

Volvo D12, Operator'S Manual

Introducing the YEECORE D12 - your ultimate companion for all your audio needs. Easily learn how to unleash its full potential with our comprehensive User Manual, available for free download at manualshive.com. Discover the enhanced features and step-by-step instructions to optimize your audio experience with the YEECORE D12.

Share
Download
background image

Maintenance

145

Air Tanks

WARNING

When draining the air tanks, do not look
into the area of the draining air. Dirt or
sludge particles may be in the air stream
that could cause eye injury.

Air tanks should be drained daily. Make
sure the drain cocks close properly after
draining. Empty moisture from air tanks by
pulling the drain valve wire. The tanks
should be checked for condensation fluid,
even if an automatic drain valve is installed.

It is very important that the air system is
kept clean. Air reservoirs should be drained
daily or even twice a day on very hot days.
Daily drainage expels any condensation in
the air reservoirs. If sludge or oil is found
in the drainage, the air compressor should
be checked for proper operation.

If an excessive amount of fluid is drained
out of the tanks (even when drained daily)
have the system checked for possible prob-
lems with the air dryer.

W5001203

Air Dryers

Air dryers have a regeneration system that
cleans out the accumulated moisture but
eventually the drying medium will be filled
up. Change the dryer cartridge when more
water than usual is noticed at the daily tank
drainings. The volume of daily drain water
will change depending on temperature, geo-
graphical location and how much the
brakes are used.

Dryer manufacturers recommends changing
the cartridge every 2 to 3 years but the in-
tervals need to be adjusted for vehicle
application. In hot, coastal climates, the car-
tridge may have to be changed every year.

Summary of Contents for D12























































































































































































































Reviews:

No comments

Related manuals for D12

M+S MM Series Service Manual preview
MM Series
Brand: M+S Pages: 6
ACM TRONIX 13 Instructions And Warnings For Fitters preview
TRONIX 13
Brand: ACM Pages: 37
PCM 2003 5.0L MPI Owner'S Operation And Maintenance Manual preview
2003 5.0L MPI
Brand: PCM Pages: 83
Northern Lights NL773LW4 Operator'S Manual preview
NL773LW4
Brand: Northern Lights Pages: 42
Volvo Penta IPS 3 Installation Reference Manual preview
IPS 3
Brand: Volvo Penta Pages: 1
Volvo Penta MB 10 A Instruction Book preview
MB 10 A
Brand: Volvo Penta Pages: 15
Volvo Penta D4-SOLAS Operator'S Manual preview
D4-SOLAS
Brand: Volvo Penta Pages: 76
Volvo Penta D5 Operator'S Manual preview
D5
Brand: Volvo Penta Pages: 80
Volvo Penta D9-425 Operator'S Manual preview
D9-425
Brand: Volvo Penta Pages: 88
Volvo Penta 230 Workshop Manual preview
230
Brand: Volvo Penta Pages: 102
Volvo Penta D11 Operator'S Manual preview
D11
Brand: Volvo Penta Pages: 108
Volvo Penta D4-260 Operator'S Manual preview
D4-260
Brand: Volvo Penta Pages: 124
TCF DCRD Installation, Operation & Maintenance Manual preview
DCRD
Brand: TCF Pages: 16
Eastwood 13542 Instructions Manual preview
13542
Brand: Eastwood Pages: 20
Powertrain 8.0L LPG V8 Operator'S Manual preview
8.0L LPG V8
Brand: Powertrain Pages: 36
Briggs & Stratton 12J800 Series Illustrated Parts List preview
12J800 Series
Brand: Briggs & Stratton Pages: 16
Hobbico AQUACRAFT .18 MARINE Instructions preview
AQUACRAFT .18 MARINE
Brand: Hobbico Pages: 4
Mitsubishi S 12 R User And Maintenance Manual preview
S 12 R
Brand: Mitsubishi Pages: 88

Brands by name

Popular brands

Load more brands