background image

– Turn adjustment screw -arrow A- to adjust beam range.
There is no provision for lateral adjustment.

Note

The adjuster screw for the left fog light is a mirror image.

Other additional lights
Additionally retrofitted lights of other systems must be checked

and set according to valid guidelines.

4.52

Sliding sunroof drains: checking for

blockage, cleaning if necessary

Open sliding sunroof completely.
– Check water drain at front -arrows- for contamination, and

clean if necessary.

– Carefully pour tap water from a measuring beaker into water

drain at front. Proceed with caution to make sure no water en‐

ters the vehicle interior.

– Check under vehicle if water emerges in area of front wheel

housing.

– Repeat procedure on other side of vehicle.
– If no water emerges at relevant positions, clean sunroof

drains.

Note

Cleaning of the sliding sunroof drains is a repair measure which

is subject to a separate charge when performed.

4.53

Service interval display: resetting

Resetting service interval display using vehicle diagnostic tester

⇒ page 150

Resetting service interval display without vehicle diagnostic tester

⇒ page 150

Additional information for service interval display 

⇒ page 5

The service interval display must be reset (adapted) during
♦ delivery inspection
♦ Every oil change service and interval service.
♦ each oil change (flexible/fixed)
.
Until now, only service events linked to oil changes could be dis‐

played in the service interval display. Service stickers have been

used for all other service events.

Model year

Service interval display for oil

change service / interval service

(channel 1)

Service interval display for inspec‐

tion service (channel 2)

►2013

yes

no

Passat 2011 ➤ , Passat Variant 2011 ➤

Maintenance - Edition 01.2019

4. Descriptions of work:    

149

Summary of Contents for Passat 2011





























































































































































































Reviews: