Volkswagen Passat 2011 Maintenance Manual Download Page 46

Page: 46 / 188

4.5

Battery: checking battery terminal

clamps for secure seating

Battery in engine compartment

⇒ page 42

Battery in luggage compartment

⇒ page 44

Special tools and workshop equipment required
♦ Torque wrench - V.A.G 1331-

Note

♦

A securely seated battery terminal clamp ensures trouble free

function and long service life of the battery.

♦

When securing terminal clamp, ensure that it is completely

seated on battery terminal.

4.5.1

Battery in engine compartment

Carry out following procedure:
– Open battery cladding cover (if fitted).

– Check whether battery terminal clamps are secure on battery

terminals by moving battery positive cable and battery nega‐

tive cable back and forth.

WARNING

If the battery terminal clamp is not seated securely on the bat‐

tery positive terminal, first disconnect battery terminal clamp

on battery negative terminal to prevent possible accidents.

If the battery terminal clamp is NOT seated securely on positive

terminal:

Passat 2011 ➤ , Passat Variant 2011 ➤

Maintenance - Edition 01.2019

4. Descriptions of work:

Summary of Contents for Passat 2011





























































































































































































Search results

Summary of Contents for Passat 2011

Reviews:

Related manuals for Passat 2011

Brands by name

Popular brands

Volkswagen Passat 2011, Maintenance Manual

Search results

Summary of Contents for Passat 2011

Reviews:

Related manuals for Passat 2011

Brands by name

Popular brands