Volkswagen Passat 2011 Maintenance Manual Download Page 124

Page: 124 / 188

♦ Automatic gearbox: Selector lever position, shift lock/ignition

key removal lock, shift behaviour, dash panel insert display

♦ Foot brake and handbrake: function, free travel and effective‐

ness, pulling to one side, juddering, squeal

♦ ABS function: pulsing must be felt at the brake pedal during

ABS-regulated braking

♦ Steering: function, steering free clearance, steering wheel

centred when vehicle is travelling straight ahead

♦ Tilting roof: function
♦ Radio/radio navigation system: function, reception, GALA, in‐

terference noise

♦ Multi-function indicator (MFI): functions
♦ Air conditioning system: check function (At low temperatures

the function of air conditioner must be checked in a workshop).

♦ Vehicle: pulls to one side when travelling straight ahead (level

road).

♦ Imbalance: wheels, drive shafts, propshaft
♦ Noise/vibration: wheel bearing, exhaust system
♦ Engine: hot starting behaviour

4.41

Wheel securing bolts: tightening to

specified torque

♦ Pulling off wheel hub trim:

⇒ page 120

♦ Pulling off wheel trim

⇒ page 121

♦ Pulling off wheel bolt caps:

⇒ page 121

♦ Loosening/tightening anti-theft wheel bolts

⇒ page 121

♦ Tightening wheel bolts

⇒ page 122

♦ Installing wheel centre cover, wheel bolt cover caps and wheel

cover

⇒ page 122

Pulling off wheel hub trim

Caution

On vehicles with light alloy wheels do not lever wheel hub trim

off with screwdriver, only use the special tool for this purpose

(puller hook in vehicle tool kit).

The puller hook -1- to remove the cover caps is located with the

vehicle tool kit.
– Hook puller hook into one drilling of wheel hub trim and pull off

in -direction of arrow-.

Passat 2011 ➤ , Passat Variant 2011 ➤

Maintenance - Edition 01.2019

120

4. Descriptions of work:

Summary of Contents for Passat 2011





























































































































































































Search results

Summary of Contents for Passat 2011

Reviews:

Related manuals for Passat 2011

Brands by name

Popular brands

Volkswagen Passat 2011, Maintenance Manual

Search results

Summary of Contents for Passat 2011

Reviews:

Related manuals for Passat 2011

Brands by name

Popular brands