Volkswagen Passat 2011 Maintenance Manual Download Page 168

Page: 168 / 188

– Disengage clamps of cable guide -arrows-.
– Remove hoses -1- and -2-.

Note

♦

When pulling out the ignition coils with output stages, the wires

or ignition coil connectors can remain connected.

♦

Note installation position of ignition coils with output stages.

Caution

Ensure that the cables are not kinked or damaged.

– Place puller - T10094 A- on ignition coil with output stage

-arrow-.

– Slightly pull out ignition coil with output stage.
– Fit assembly tool - T10118- as illustrated.
– Release connector locking device carefully and pull off con‐

nector.

– Unscrew spark plugs using spark plug socket - VAS 3122B- .
Installing:

Note

♦

When installing new spark plugs, regrease ignition coils with

output stage using silicone paste ⇒ ETKA .

♦

The applicable silicone paste is stated in the ETKA along with

the corresponding ignition coil and/or spark plug.

Passat 2011 ➤ , Passat Variant 2011 ➤

Maintenance - Edition 01.2019

164

4. Descriptions of work:

Summary of Contents for Passat 2011





























































































































































































Search results

Summary of Contents for Passat 2011

Reviews:

Related manuals for Passat 2011

Brands by name

Popular brands

Volkswagen Passat 2011, Maintenance Manual

Search results

Summary of Contents for Passat 2011

Reviews:

Related manuals for Passat 2011

Brands by name

Popular brands