Volkswagen Passat 2011 Maintenance Manual Download Page 24

Page: 24 / 188

Scope of work

Interval

Gearbox mounting: renew

• Applies only to Phaeton with towing bracket

Every 150,000 km

Diesel particulate filter: check.

At 180,000 km/210,000 km,

then every 30,000 km

All-wheel drive coupling: changing oil

Every 3 years

Natural gas system: inspect natural gas tank for cor‐

rosion and leakage.

• Europe only (except for Italy)

3 years after initial registration,

then every 2 years

Natural gas filler connection and sealing cap: check

condition, clean if necessary and check seal.

• Europe only (except for Italy)

3 years after initial registration,

then every 2 years

Reducing agent (AdBlue

/DEF): changing

• Applies only to vehicles driven less than 15,000 km

in 4 years

Every 4 years

Natural gas tank: renew.

Every 20 years

Passat 2011 ➤ , Passat Variant 2011 ➤

Maintenance - Edition 01.2019

2. Service work

Summary of Contents for Passat 2011





























































































































































































Search results

Summary of Contents for Passat 2011

Reviews:

Volkswagen Passat 2011, Maintenance Manual, Page: 24 / 188

Search results

Summary of Contents for Passat 2011

Reviews: