Volkswagen Passat 2011 Maintenance Manual Download Page 78

Page: 78 / 188

Part number - 3AA 010 804 C-

Passat Estate

Half payload

kPa/bar/psi

Full payload

kPa/bar/psi

Tyre size

Front

Rear

Front

Rear

205/50 R17

250/2.5/36

280/2.8/41

320/3.2/46

235/40 R18

4.10.7

Tyre pressures, Passat Estate "Alltrack"

Note

♦

During delivery inspection, check that tyre inflation pressure

sticker is fitted. If the sticker is missing, order a new sticker

through ETKA.

♦

The mandatory tyre pressures for the respective model can be

found on a sticker attached to the inside of tank flap or to the

B-pillar.

♦

If the inflation pressure sticker is missing, proceed as follows:

♦

Locate correct part number for respective vehicle in ETKA.

♦

Using part number, determine respective inflation pressures

in tyre inflation table.

♦

Uniform pressure: if tyre sizes are not shown for a part number,

then a uniform pressure is valid for all authorised wheel/tyre

combinations. ⇒ Wheels and Tyres Guide; Rep. gr. 44 ;

Wheel and tyre combinations .

Check tyre pressure using tyre inflator - VAS 5216- , correct if

necessary.

Part number - 3AA 010 819 G-

Passat Estate "Alltrack"

Part number - 3AA 010 819 K-
Part number - 3AA 010 000 G-

Half payload

kPa/bar/psi

Full payload

kPa/bar/psi

Tyre size

Front

Rear

Front

Rear

225/50 R17

220/2.2/32

240/2.4/35

280/2.8/41

225/45 R18

205/50 R17 M&S

250/2.5/36

270/2.7/39

310/3.1/45

215/55 R16

340/3.4/49

Spare wheel

Part number - 3AA 010 819 F-

Passat Estate "Alltrack"

Part number - 3AA 010 819 J-

Half payload

kPa/bar/psi

Full payload

kPa/bar/psi

Tyre size

Front

Rear

Front

Rear

225/50 R17

220/2.2/32

240/2.4/35

280/2.8/41

225/45 R18

205/50 R17 M&S

240/2.4/35

260/2.6/38

300/3.0/44

Passat 2011 ➤ , Passat Variant 2011 ➤

Maintenance - Edition 01.2019

4. Descriptions of work:

Summary of Contents for Passat 2011





























































































































































































Search results

Summary of Contents for Passat 2011

Reviews:

Related manuals for Passat 2011

Brands by name

Popular brands

Volkswagen Passat 2011, Maintenance Manual

Search results

Summary of Contents for Passat 2011

Reviews:

Related manuals for Passat 2011

Brands by name

Popular brands