Vivotek AW-IHT-1270 User Manual Download Page 86

Page: 86 / 228

Port Settings

Parameter

Description

Port

Select a port number to configure from the drop-down box.
Select

All

to configure all ports at the same time.

PVID

Select a

PVID

(Port VLAN ID number) from the drop-down box.

Acceptable Frame

Specify the type of frames allowed on a port. Choices are

All

VLAN

Untagged Only

VLAN Tagged Only

- Select

All

from the drop-down list box to accept all untagged or

tagged frames on this port. This is the default setting.
- Select

VLAN Tagged Only

to accept only tagged frames on this port.

All untagged frames will be dropped.
- Select

VLAN Untagged Only

to accept only untagged frames on this

port. All tagged frames will be dropped.

Apply

Click Apply to save your changes back to the Switch.

Refresh

Click Refresh to begin configuring this screen afresh.

Port Status

Port

This field displays the port number.

PVID

This field displays the Port VLAN ID number.

Acceptable Frame

This field displays the type of frames allowed on the port. This will
either display

All

VLAN

Tagged Only or VLAN Untagged Only.

Summary of Contents for AW-IHT-1270





































































































































































































































Search results

Summary of Contents for AW-IHT-1270

Reviews:

Brands by name

Popular brands

Vivotek AW-IHT-1270, User Manual

Search results

Summary of Contents for AW-IHT-1270

Reviews:

Brands by name

Popular brands