manualshive.com logo in svg

Vivotek AW-IHT-1270, User Manual

Share
Download
Vivotek AW-IHT-1270 User Manual Download Page 141

 

133 

 

<IPv4_ADDR> 
<MAC_ADDR> 

ARP table. 

configure  no ipv6 arp   

<IPv6_ADDR> 
<MAC_ADDR> 

This command deletes a static IPv6 ARP entry from 
ARP table. 

configure  interface vlan VLAN-

ID 

This command enters the L3 interface node. 

L3 
interface 

ipv4 address 
A.B.C.D/M 

This command assigns a specified IPv4 interface route 
to the interface. 
We can assign multiple IPv4 interface route to a single 
interface with different IP segment. 
If this configuration is a first IP assigning to the 
interface then automatically interface is enabled for 
routing. 

L3 
interface 

ipv6 address 
<IPv6_ADDR>/M 

This command assigns a specified IPv6 interface route 
to the interface. 
We can assign only one IPv6 interface route for an 
interface vlan. 
If this configuration is a first IP assigning to the 
interface then it automatically enables the interface with 
routing. 

L3 
interface 

no ipv4 address 
A.B.C.D/M 

This command deletes a specified IPv4 interface route 
from the interface vlan. 
This command deletes all dependent static routes on the 
specified IPv4 interface route. 
If there is no assigned IP addresses for the specified 
interface after deleting then it will automatically 
disables routing in interface.   

L3 
interface 

no ipv4 address 
<IPv6_ADDR>/M 

This command deletes a specified IPv6 interface route 
from the interface. 
This command deletes all dependent static routes on the 
specified IPv6 interface route. 
If there is no assigned IP addresses for the specified 
interface after deleting then it will automatically 
disables routing in interface vlan. 

L3 
interface 

ipv4 route 
A.B.C.D/M A.B.C.D 

This command configures an IPv4 static route onto the 
specified interface vlan. 

L3 
interface 

ipv6 route 
<IPv6_ADDR>/M 
<IPv6_ADDR> 

This command configures an IPv6 static route onto the 
specified interface vlan. 

L3 
interface 

no ipv4 route 
A.B.C.D/M A.B.C.D 

This command deletes a specified IPv4 static route from 
an interface vlan. 

L3 
interface 

no ipv6 route 
<IPv6_ADDR>/M 
<IPv6_ADDR> 

This command deletes a specified IPv6 static route from 
an interface vlan. 

 

Summary of Contents for AW-IHT-1270





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands