manualshive.com logo in svg

Vivotek AW-IHT-1270, User Manual

Share
Download
Vivotek AW-IHT-1270 User Manual Download Page 211

 

203 

 

Community String 

Specify the community string used with this remote trap station. 

Apply 

Click 

Apply 

to configure the settings. 

Refresh 

Click 

Refresh 

to begin configuring this screen afresh. 

Trap Receiver List 

No. 

This field displays the index number of the trap receiver entry. Click the 
number to modify the entry. 

IP Address 

This field displays the IP address of the remote trap station. 

Version 

This field displays the version of Simple Network Management Protocol 
in use. 

v1 

or 

v2c

. 

Community String 

This  field  displays  the  community  string  used  with  this  remote  trap 
station. 

Action 

Click 

Delete 

to remove a configured trap receiver station. 

 
 

9.1.3.

 

SNMPv3 

9.1.3.1.

 

CLI Configuration 

Node 

Command 

Description 

enable 

show snmp user 

This command displays all snmp v3 users. 

enable 

show snmp group 

This command displays all snmp v3 groups. 

enable 

show snmp view 

This command displays all snmp v3 view. 

configure 

snmp user USERNAME 
GROUPNAME noauth 

Configures v3 user of non- authentication. 

configure 

snmp user USERNAME 
GROUPNAME auth 
(MD5|SHA) STRINGS 

Configures v3 user of authentication. 

configure 

snmp user USERNAME 
GROUPNAME priv 
(MD5|SHA) STRINGS des 
STRINGS 

Configures v3 user osnmf authentication and 
encryption. 

configure 

snmp group GROUPNAME 
noauth (read STRINGS write 
STRINGS notify STRINGS) 

Configures v3 group of non- authentication. 

configure 

snmp group GROUPNAME 
auth (read STRINGS write 
STRINGS notify STRINGS) 

Configures v3 group of authentication. 

configure 

snmp group GROUPNAME 
priv (read STRINGS write 
STRINGS notify STRINGS) 

Configures v3 group of authentication and 
encryption. 

Summary of Contents for AW-IHT-1270





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands