Vivotek AW-IHT-1270 User Manual Download Page 76

Page: 76 / 228

224.0.0.13

PIM Version 2 (Protocol Independent Multicast)

224.0.0.18

Virtual Router Redundancy Protocol

224.0.0.19 - 21

IS-IS over IP

224.0.0.22

IGMP Version 3 (Internet Group Management Protocol)

224.0.0.102

Hot Standby Router Protocol Version 2

224.0.0.251

Multicast DNS address

224.0.0.252

Link-local Multicast Name Resolution address

224.0.1.1

Network Time Protocol address

224.0.1.39

Cisco Auto-RP-Announce address

224.0.1.40

Cisco Auto-RP-Discovery address

224.0.1.41

H.323 Gatekeeper discovery address

6.2.5.2.

CLI Configuration

Node

Command

Description

enable

show mac-address-table
multicast

This command displays the current
static/dynamic multicast address entries.

enable

show mac-address-table
multicast vlan VLANID

This command displays the current
static/dynamic multicast address entries with
a specific vlan.

configure mac-address-table multicast

MACADDR vlan VLANID
ports PORTLIST

This command configures a static multicast
entry.

configure no mac-address-table multicast

MACADDR

This command removes a static multicast
entry from the address table.

6.2.5.3.

Web Configuration

Parameter

Description

Summary of Contents for AW-IHT-1270





































































































































































































































Search results

Summary of Contents for AW-IHT-1270

Reviews:

Brands by name

Popular brands

Vivotek AW-IHT-1270, User Manual

Search results

Summary of Contents for AW-IHT-1270

Reviews:

Brands by name

Popular brands