Vivotek AW-IHT-1270 User Manual Download Page 183

Page: 183 / 228

175

profile.

acl

destination mac host
MACADDR

This command configures the destination MAC and
mask for the profile.

acl

destination mac
MACADDR
MACADDR

This command configures the destination MAC and
mask for the profile.

acl

destination mac
MACADDR
MACADDR

This command configures the destination MAC and
mask for the profile. The second MACADDR parameter
is the mask for the profile.

acl

no destination mac

This command removes the destination MAC from the
profile.

acl

ethertype STRING

This command configures the ether type for the profile.
Where the STRING is a hex-decimal value. e.g.: 08AA.

acl

no ethertype

This command removes the limitation of the ether type
from the profile.

acl

source mac host
MACADDR

This command configures the source MAC and mask
for the profile.

acl

source mac
MACADDR
MACADDR

This command configures the source AMC and mask
for the profile.

acl

no source mac

This command removes the source MAC and mask
from the profile.

acl

source ip host
IPADDR

This command configures the source IP address for the
profile.

acl

source ip IPADDR
IPMASK

This command configures the source IP address and
mask for the profile.

acl

no source ip

This command removes the source IP address from the
profile.

acl

destination ip host
IPADDR

This command configures a specific destination IP
address for the profile.

acl

destination ip
IPADDR IPMASK

This command configures the destination IP address and
mask for the profile.

acl

no destination ip

This command removes the destination IP address from
the profile.

acl

l4-source-port
IPADDR

This command configures UDP/TCP source port for the
profile.

acl

no l4-source-port
IPADDR

This command removes the UDP/TCP source port from
the profile.

acl

L4-destination-port
PORT

This command configures the UDP/TCP destination
port for the profile.

acl

no l4-destination-port This command removes the UDP/TCP destination port

from the profile.

acl

vlan VLANID

This command configures the VLAN for the profile.

acl

no vlan

This command removes the limitation of the VLAN
from the profile.

acl

source interface

This command configures the source interface for the

Summary of Contents for AW-IHT-1270





































































































































































































































Search results

Summary of Contents for AW-IHT-1270

Reviews:

Brands by name

Popular brands

Vivotek AW-IHT-1270, User Manual

Search results

Summary of Contents for AW-IHT-1270

Reviews:

Brands by name

Popular brands