manualshive.com logo in svg

Vivotek AW-IHT-1270, User Manual

Share
Download
Vivotek AW-IHT-1270 User Manual Download Page 157

 

149 

 

enable 

show spanning-tree 
mst instance 

This command displays all of the instance 
configurations of the MSTP. 

enable 

show spanning-tree 
mst instance <0-63> 

This command displays specific instance configurations 
of the MSTP. 

enable 

show spanning-tree 
mst instance <0-63> 
interface IFNAME 

This command displays specific instance configurations 
on an interface of the MSTP. 

enable 

show spanning-tree 
mst interface 
IFNAME 

This command displays the configurations on an 
interface of the MSTP. 

enable 

show spanning-tree 
mst root 

This command displays the root bridge configurations. 

configure  spanning-tree 

(disable|enable) 

This command enables / disables the spanning tree. 

configure  spanning-tree mode 

mst 

This command configures the mode of the spanning 
tree. (one of the three modes STP/RSTP/MSTP.) 

configure  spanning-tree mst 

forward-time 

This command configures the forward time for the 
MSTP. 

configure  no spanning-tree mst 

forward-time 

This command resets the forward time for the MSTP.   
The default forward delay time is 15 seconds. 

configure  spanning-tree mst 

hello-time 

This command configures the hello time for the MSTP. 

configure  no spanning-tree mst 

hello-time 

This command resets the hello time for the MSTP. 
The default hello time is 2 seconds. 

configure  spanning-tree mst 

max-age 

This command configures the maximum age time for 
the MSTP. 

configure  no spanning-tree mst 

max-age 

This command resets the maximum age time for the 
MSTP. 
The default maximum age time is 20 seconds. 

configure  spanning-tree mst 

max-hops 

This command configures the maximum hop count. 

configure  no spanning-tree mst 

max-hops 

This command resets the maximum hop count. 
The default maximum hop count is 20. 

configure  spanning-tree mst 

instance STRING 
priority <0-61440> 

This command resets the maximum hop count. 
The default maximum hop count is 20. 

configure  no spanning-tree mst 

instance STRING 
priority 

This command resets the priority for the specific 
instance. 

interface 

spanning-tree mst 
instance STRING 
cost <1-200000000> 

This command configures a cost on the specific port for 
the MSTP. 

interface 

no spanning-tree mst 
instance STRING 
cost 

This command resets the cost on the specific port for the 
MSTP. 

interface 

spanning-tree mst 

This command configures a priority on the specific port 

Summary of Contents for AW-IHT-1270





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands