manualshive.com logo in svg

Vivotek AW-IHT-1270, User Manual

Share
Download
Vivotek AW-IHT-1270 User Manual Download Page 62

 

54 

 

enable 

show igmp-snooping 
counters 

This command displays the current IGMP snooping 
counters. 

enable 

show igmp-snooping 
querier 

This command displays the current IGMP Queriers. 

enable 

show multicast 

This command displays the multicast group in IP 
format. 

configure  clear igmp-snooping 

counters 

This command clears all of the IGMP snooping 
counters. 

configure    igmp-snooping 

(disable | enable) 

This command disables / enables the IGMP snooping 
on the switch. 

configure  igmp-snooping vlan 

VLANID 

This command enables the IGMP snooping function on 
a VLAN or range of VLANs. 

configure  no igmp-snooping 

vlan VLANID 

This command disables the IGMP snooping function 
on a VLAN or range of VLANs. 

configure  igmp-snooping 

unknown-multicast 
(drop|flooding) 

This command configures the process for unknown 
multicast packets when the IGMP snooping function is 
enabled. 

drop: 

Drop all of the unknown multicast packets. 

 

configure  igmp-snooping 

report-suppression 
(disable|enable) 

This command disables / enables the IGMP snooping 
report suppression function on the switch. 

configure  clear igmp-counters 

This command clears the IGMP snooping counters. 

configure  clear igmp-counters 

(port|vlan) 

This command clears the IGMP snooping counters for 
port or vlan. 

interface 

igmp-querier-mode 
(auto|fixed|edge) 

This command specifies whether or not and under what 
conditions the port(s) is (are) IGMP query port(s). The 
Switch forwards IGMP join or leave packets to an 
IGMP query port, treating the port as being connected 
to an IGMP multicast router (or server). You must 
enable IGMP snooping as well. (Default:auto) 

interface 

igmp-immediate-
leave   

This command enables the IGMP Snooping immediate 
leave function for the specific interface. 

interface 

no igmp-immediate-
leave 

This command disables the IGMP Snooping immediate 
leave function for the specific interface. 

interface 

igmp-snooping group-
limit VALUE 

This command configures the maximum groups for the 
specific interface. 

interface 

no igmp-snooping 
group-limit 

This command removes the limitation of the maximum 
groups for the specific interface. 

configure  interface range   

gigabitethernet1/0/ 
PORTLISTS 

This command enters the interface configure node. 

if-range 

igmp-immediate-
leave   

This command enables the IGMP Snooping immediate 
leave function for the specific ports. 

if-range 

no igmp-immediate-
leave 

This command disables the IGMP Snooping immediate 
leave function for the specific ports. 

Summary of Contents for AW-IHT-1270





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands