manualshive.com logo in svg

Vivotek AW-IHT-1270, User Manual

Share
Download
Vivotek AW-IHT-1270 User Manual Download Page 64

 

56 

 

Report 

Suppression 

State 

Select 

Enable/Disable 

to activate/deactivate IGMP Snooping report 

suppression function. 

IGMP 

Snooping 

VLAN State 

Select 

Add 

and enter VLANs upon which the Switch is to perform 

IGMP  snooping.  The  valid  range  of  VLAN  IDs  is  between  1  and 
4094.  Use  a  comma  (,)  or  hyphen  (-)  to  specify  more  than  one 
VLANs. Select 

Delete 

and enter VLANs on which to have the Switch 

not perform IGMP snooping. 

Unknown 

Multicast 

Packets 

Specify the action to perform when the Switch receives an unknown 
multicast frame. Select 

Drop 

to discard the frame(s). Select 

Flooding 

to send the frame(s) to all ports. 

Apply 

Click Apply to configure the settings. 

Refresh 

Click this to reset the fields to the last setting. 

IGMP Snooping State 

This  field  displays  whether  IGMP  snooping  is  globally  enabled  or 
disabled. 

Report 

Suppression 

State 

This  field  displays  whether  IGMP  snooping  report  suppression  is 
enabled or disabled. 

IGMP 

Snooping 

VLAN State 

This field displays VLANs on which the Switch is to perform IGMP 
snooping. None displays if you have not enabled IGMP snooping on 
any port yet. 

Unknown Multicast 
Packets 

This  field  displays  whether  the  Switch  is  set  to  discard  or  flood 
unknown multicast packets. 

 

Port Settings 

 

 

Parameter 

Description 

Querier Mode 

Select the desired setting, 

Auto

, 

Fixed

, or 

Edge

. 

Auto

 means the 

Switch uses the port as an IGMP query port if the port receives IGMP 

Summary of Contents for AW-IHT-1270





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands