Vidikron VDP-720 Owner'S Operating Manual Download Page 15

Page: 15 / 56

Introduction

Vidikron VDP-80-720 Owner’s Operating Manual

PRE

IMINAR

Key Features and Benefits

The VDP-80-720 offers these key features and benefits:

•

Ten inputs (2 Composite/SVideo, 2 Composite/SVideo/SD-Component, 2 SD/HD
Component/RGB, 2 DVI-D and 2 SDI)

•

Video processing/deinterlacing is supported for HDCP encrypted DVI-D inputs

•

Component/RGB analog and DVI-D input accept 720p and 1080i sources

•

Transcoding (for example, component to RGB) for digital and analog inputs

•

3:2, 3:3 and 2:2 film pull-down frame-reconstruction for SD sources

•

Per-pixel motion-adaptive video deinterlacing for SD sources

•

Multiple, independent configuration memories for each input

•

Black-level and contrast calibration per memory

•

Color, red-color-offset, green-color-offset calibration per memory

•

Hue, red-hue-offset, green-hue-offset calibration per memory

•

Y/C delay calibration with independent CB and CR delay

•

Detail enhancing scaler

•

Programmable vertical refresh rate

•

Programmable screen aspect ratio

•

DVI-D output with HDCP encryption support

•

BNC analog output

•

Backlit infrared remote control with on-screen menu system

•

RS232 serial interface for control and software updates

•

Silent operation (no fan)

Summary of Contents for VDP-720

























































Search results

Summary of Contents for VDP-720

Reviews:

Related manuals for VDP-720

Brands by name

Popular brands

Vidikron VDP-720, Owner'S Operating Manual

Search results

Summary of Contents for VDP-720

Reviews:

Related manuals for VDP-720

Brands by name

Popular brands