VAT 95248-PAGI-0002 Installation, Operating, & Maintenance Instructions Download Page 79

Page: 79 / 81

Installation, Operating & Maintenance Instructions

Series 612 DN 250 (I.D. 10”), EtherCAT

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

282408EB

2012-04-23

79/81

Spare parts

Please specify the

fabrication number of the valve

(see yellow label on valve) when ordering spare parts.

This is to ensure that the appropriate spare parts are supplied.

7.1 Control and actuating unit

Item

Description

Valve size
Product ordering number

All sizes

612 . . - . . . .

Control and actuating unit

536301

Option board with SPS module

(±15VDC sensor power supply)

378000

Option board with PFO module

(power failure option)

378002

Option board

with SPS and PFO module

376837

7.2 Valve unit

Item

Description

Part number

Spare parts kit

body with mechanism

536481 (with insert)

Spare parts kit shaft kit

489910

Spare parts kit valve body

430607

Spare parts kit plate

241208

Plate screw

353386

7.3 Seals and grease

Item

Description

Part number

Rotary feed through seals kit

none

Rotary feed
through seals

atmosphere
(Viton)

N-5100-204

vacuum
(Viton)

N-5100-204

Vacuum grease syringe

206792 (2ml), 206793 (5ml)

Summary of Contents for 95248-PAGI-0002


















































































Search results

Summary of Contents for 95248-PAGI-0002

Reviews:

Brands by name

Popular brands

VAT 95248-PAGI-0002, Installation, Operating, & Maintenance Instructions

Search results

Summary of Contents for 95248-PAGI-0002

Reviews:

Brands by name

Popular brands