VAT 95248-PAGI-0002 Installation, Operating, & Maintenance Instructions Download Page 14

Page: 14 / 81

Installation, Operating & Maintenance Instructions

Series 612 DN 250 (I.D. 10”), EtherCAT

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel +41 81 771 61 61 Fax +41 81 771 48 30 [email protected] www.vatvalve.com

282408EB

2012-04-23

14/81

2.6 Electrical connection

2.6.1 Ground connection

Recommendation for ground strap between controller and system (chassis)

Material

L (Length max.)

B1 (min.)

B2 (min.)

d1 ( )

d2 ( )

copper tinned

200 mm

25 mm

4.5 mm

customized

Note:

Connection plates of ground strap must be total plane for a good electrical contact!

Note:

The connection point at chassis (FE) must be blank metal (not coated).

It is also possible to connect the ground strap at system chamber if it is well connected to PE.

Note:

Avoid low chassis cross section to the system PE connection. (Min. same cross section as ground strap)

Valve controller

System

Ground connection

Chassis (FE)

(Functional Earth)

Ground strap

Recommended torque

: 1,3…1,7Nm

Summary of Contents for 95248-PAGI-0002


















































































Search results

Summary of Contents for 95248-PAGI-0002

Reviews:

Brands by name

Popular brands

VAT 95248-PAGI-0002, Installation, Operating, & Maintenance Instructions

Search results

Summary of Contents for 95248-PAGI-0002

Reviews:

Brands by name

Popular brands