manualshive.com logo in svg

VAT 95248-PAGI-0002, Installation, Operating, & Maintenance Instructions

Share
Download
VAT 95248-PAGI-0002 Installation, Operating, & Maintenance Instructions Download Page 17

 

Installation, Operating & Maintenance Instructions 

Series 612 DN 250 (I.D. 10”), EtherCAT

 

 

 

 

VAT Vakuumventile AG, CH-9469 Haag, Switzerland 

Tel +41 81 771 61 61   Fax +41 81 771 48 30   [email protected]   www.vatvalve.com

 

282408EB

 

2012-04-23 

17/81 

 

 

2.6.3.2 

Sensor power wiring external 

 

 

Note: 

 

Use shielded sensor cable(s). Keep cable as short as possible, but locate it away from noise sources. 

 

Connect the +24 VDC sensors at DB

–15 female sensor connector exactly as shown in the drawing above. Do not 

connect other pins, that may damage power supply or controller! 

 

Connector: Use only screws with 4-40UNC thread for fastening the connectors! 

 

Pins 4 and 8 must be bridged for operation! 

An optional switch would allow for motor 
interlock to prevent valve from moving.

 

Summary of Contents for 95248-PAGI-0002


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands