manualshive.com logo in svg

VAT 95248-PAGI-0002, Installation, Operating, & Maintenance Instructions

Share
Download
VAT 95248-PAGI-0002 Installation, Operating, & Maintenance Instructions Download Page 15

 

Installation, Operating & Maintenance Instructions 

Series 612 DN 250 (I.D. 10”), EtherCAT

 

 

 

 

VAT Vakuumventile AG, CH-9469 Haag, Switzerland 

Tel +41 81 771 61 61   Fax +41 81 771 48 30   [email protected]   www.vatvalve.com

 

282408EB

 

2012-04-23 

15/81 

 

2.6.2  Sensor supply concepts 

 
This valve offers 2 alternative concepts to supply the sensor(s) with power. This depends on the sensor type that is used. 
Optional is this valve available with an sensor power supply module (SPS) that converts  15 VDC from the 24 VDC. 
 
Concepts: 

 

 

Ex 24 VDC supplied to POWER connector is feed through to SENSOR connector to supply 24 VDC 
sensors. Refer to chapter «Power and sensor connection (+24 VDC sensors)» for schematic and correct wiring. 

 

 

 

External  15 VDC supplied to POWER connector is feed through to SENSOR connector to supply  15 VDC 
sensors. Refer to chapter «Power and sensor connection ( 15 VDC sensors) without optional SPS module» for 
schematic and correct wiring. 

 
Valve versions: 

 

 

612 . . - . . 

G

 . - . . . .  and 612 . . - . . 

H

 . - . . . .   

SPS module not included 

 
 

Note: 

The SPS module can be retrofitted. Refer to chapter «Retrofit / replacement procedure» for instruction. 

 

Summary of Contents for 95248-PAGI-0002


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands