Vari Lite VL10 BeamWash, User Manual, Page: 75 / 85

61
Troubleshooting
Error Messages
If a problem occurs during luminaire calibration, at the end of the calibration sequence the
Menu Display will cycle through any applicable error message(s) until the end of the list is
reached. To review the error messages again, it will be necessary to access them using the
Status function.
To access error messages:
Step 1. Press .
Step 2. Press arrows until Fixture appears. Press .
Step 3. Press arrows to access Status. Press . (Display will now scroll
through any error messages or display OK if no errors.)
Table A-1: Error Messages
Display Message
No Errors Fixture is ok
NO Sensor On Pan Pan sensor not found, Pan ReCalibrate fail. Note:For safety, the lamp will shut off
automatically if there is a pan error on startup.
NO Sensor On Tilt Tilt sensor not found, Tilt ReCalibrate fail. Note:For safety, the lamp will shut off
automatically if there is a tilt error on startup.
NO Sensor On Cyan Cyan sensor not found, Cyan ReCalibrate fail.
NO Sensor On Magenta Magenta sensor not found, Magenta ReCalibrate fail.
NO Sensor On Yellow Yellow sensor not found, Yellow ReCalibrate fail.
NO Sensor On Color Wheel Color Wheel sensor not found, Color Wheel1 ReCalibrate fail.
NO Sensor On Rot Gobo1 Rotating Gobo1 sensor not found, Rotating Gobo1 ReCalibrate fail.
NO Sensor On Rot Gobo2 Rotating Gobo2 sensor not found, Rotating Gobo2 ReCalibrate fail.
NO Sensor On Gobo 2 Rot Rotating Gobo2 Indexing sensor not found,Rotating Gobo2 Indexing ReCalibrate fail.
NO Sensor On Rot Gobo3 Rotating Gobo3 sensor not found, Rotating Gobo3 ReCalibrate fail.
NO Sensor On Gobo3 Rot Rotating Gobo3 Indexing sensor not found, Rotating Gobo3 Indexing ReCalibrate fail.
NO Sensor On Prism Prism sensor not found, Prism ReCalibrate fail.
NO Sensor On Prism_R Prism Rotate sensor not found, Prism Rotate ReCalibrate fail.
NO Sensor On Prism 2 Prism 2 sensor not found, Prism 2 ReCalibrate fail.
NO Sensor On Prism 2_R Prism 2 Rotate sensor not found, Prism 2 Rotate ReCalibrate fail.
NO Sensor On Focus Focus sensor not found, Focus ReCalibrate fail.
NO Sensor On Zoom Zoom sensor not found, Zoom ReCalibrate fail.
NO Sensor On Frost 1 Frost1 sensor not found, Frost1 ReCalibrate fail.
NO Sensor On Frost 2 Frost2 sensor not found, Frost2 ReCalibrate fail.
NO Sensor On Flow Flow sensor not found, Flow ReCalibrate fail.
NO Sensor On Intensity Intensity sensor not found, Intensity ReCalibrate fail.
Ballast_Fault_1 Lamp over voltage(01h)
Ballast_Fault_2 Input voltage too high(02h)
Ballast_Fault_3 Temperature too high(03h)
Ballast_Fault_4 Asymmetry detected(04h)
Ballast_Fault_5 Lamp under voltage(05h)
Ballast_Fault_6 Input voltage too low(06h)
Ballast_Fault_8 NTC defective(08h)
Ballast_Fault_Other Ballast other fault(0Ah)
Ballast Over Temp Temperature too high(03h)(same Ballast_Fault_3)
Fan Fault Fan Fault
Accelerometer Err Accelerometer Err
Shift Fan Fault Shift Fan Fault
VARI LITE VL10 BeamWash User’s Manual