vacuubrand VACUU-PURE 10C Instructions For Use Manual Download

Page: 90 / 96

20901224_EN_VACUU·PURE 10C_V1.8_221122

Appendix

8.5

8.5 EC Declaration

EC Declaration of conformity

of conformity

EC Declaration of

Conformity

EG-Konformitätserklärung für Maschinen

EC Declaration of Conformity

of the Machinery

Déclaration CE de conformité des machines

Hersteller / Manufacturer / Fabricant:

VACUUBRAND GMBH + CO KG

VACUUBRAND GMBH + CO KG · Alfred-Zippe-Str. 4 · 97877 Wertheim · Germany

Hiermit erklärt der Hersteller, dass das Gerät konform ist mit den Bestimmungen der Richtlinien:

Hereby the manufacturer declares that the device is in conformity with the directives:

Par la présente, le fabricant déclare, que le dispositif est conforme aux directives:

2006/42/EG

2014/30/EU

2011/65/EU, 2015/863

Vakuumpumpe / Vacuum pump / Pompe à vide:
Typ / Type / Type:

VACUU·PURE 10C

Artikelnummer / Order number / Numéro d’article:

20751000, 20751001, 20751002, 20751003, 20751006,

20751007

Seriennummer / Serial number / Numéro de série: Siehe Typenschild / See rating plate / Voir plaque signalétique

Angewandte harmonisierte Normen / Harmonized standards applied / Normes harmonisées utilisées:
DIN EN ISO 12100:2011, DIN EN 1012-2:2011, DIN EN 61010-1:2020,

IEC 61010-1:2010 + COR:2011 + A1:2016, modifiziert / modified / modifié + A1:2016/COR1:2019

DIN EN 61326-1:2013

DIN EN IEC 63000:2019

Bevollmächtigter für die Zusammenstellung der technischen Unterlagen / Person authorised to compile the

technical file / Personne autorisée à constituer le dossier technique:

Dr. Constantin Schöler · VACUUBRAND GMBH + CO KG · Germany

Ort, Datum / place, date / lieu, date: Wertheim, 22.11.2022

ppa.

(Dr. Constantin Schöler)

(Jens Kaibel)

Geschäftsführer / Managing Director / Gérant

Technischer Leiter / Technical Director /

Directeur technique

VACUUBRAND GMBH + CO KG

VACUUBRAND GMBH + CO KG
Alfred-Zippe-Str. 4

97877 Wertheim

Tel.: +49 9342 808-0

Fax:

+49 9342 808-5555

E-Mail: [email protected]

Web:

www.vacuubrand.com

Summary of Contents for VACUU-PURE 10C

































































































Search results

Summary of Contents for VACUU-PURE 10C

Reviews:

Related manuals for VACUU-PURE 10C

Brands by name

Popular brands

vacuubrand VACUU-PURE 10C, Instructions For Use Manual

Search results

Summary of Contents for VACUU-PURE 10C

Reviews:

Related manuals for VACUU-PURE 10C

Brands by name

Popular brands