vacuubrand VACUU-PURE 10C Instructions For Use Manual Download

Page: 33 / 96

20901224_EN_VACUU·PURE 10C_V1.8_221122

Installation and connection

Check installation

conditions

Note that the

weight of

the vacuum pump

approx. 21 kg

Carefully lift the vacuum pump

out of the packaging using the

recessed grips.

4.2

4.2 Set up the vacuum pump

Set up the vacuum pump

NOTE

Condensate can damage the electronics.

A large temperature difference between the storage location

and the installation location can cause condensation.

After goods receipt or storage, allow your product to

acclimatize before initial use. The acclimatization can take

several hours.

Check installation conditions

The product is acclimatized.

The ambient conditions are within the limitation of use,



see

chapter: Observe limitation of use on page 34

Observe limitation of use on page 34

The vacuum pump must have a stable and secure base without

additional mechanical contact apart from the pump feet.

Summary of Contents for VACUU-PURE 10C

































































































Search results

Summary of Contents for VACUU-PURE 10C

Reviews:

Related manuals for VACUU-PURE 10C

Brands by name

Popular brands

vacuubrand VACUU-PURE 10C, Instructions For Use Manual

Search results

Summary of Contents for VACUU-PURE 10C

Reviews:

Related manuals for VACUU-PURE 10C

Brands by name

Popular brands