manualshive.com logo in svg

vacuubrand VACUU-PURE 10C, Instructions For Use Manual

Share
Download
vacuubrand VACUU-PURE 10C Instructions For Use Manual Download Page 38

38

20901224_EN_VACUU·PURE 10C_V1.8_221122

Installation and connection

Connect the vacuum hose

 

>

Remove the blind flange on the inlet flange.

 

>

Connect a vacuum hose with small flange KF DN 25 to the 

inlet flange, ensuring the connection is gas‑tight.

 

>

Alternatively, you can use an adapter from small flange 

KF DN 25 on the hose nozzle and attach a vacuum hose to 

it. Secure hose connections on hose nozzles, e.g., with a 

hose clip.

 

>

If necessary, install an in‑line solenoid valve or shut‑off 

valve in the inlet line to isolate your application from the 

vacuum pump with a vacuum‑tight seal.

Observe the following points for optimum results:

 

>

Keep the vacuum line as short as you can with as large a 

cross‑section as possible.

Connect the separator (AK) to the inlet (option)

 

>

Connect the separator with small flange KF DN 25 to the 

inlet flange turned forward, ensuring the connection is gas‑

tight.

 

>

Fasten the separator flask using the joint clamp.

Vacuum hose at the 

inlet

Separator at the 

inlet

Summary of Contents for VACUU-PURE 10C

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands