UniVer TC Manual Download Page 79

Page: 79 / 80

Rev.B15

Pg. 79 di 80

Damages caused by improper use

The use of original spare parts is recommended. Any modification or alteration of the product made arbitrarily by the

user is to be considered as an abuse of the conditions, so any warranty will be void.

Follow the manufacturer’s instructions and analyze any risks that the use of the component may cause within the

system where it is installed and provide for proper actions to ensure the safety of the operator.

Correct and incorrect use

The Slave Fieldbus control unit, in all its models, can only be used as indicated by the manufacturer in the operating

manual.

The safety and reliability requirements of the machine are guaranteed only by using original components and if installed

following the appropriate instructions.

Scheduled maintenance frequency

The unit was designed and built so as not to require specific scheduled maintenance.

Summary of Contents for TC

















































































Search results

Summary of Contents for TC

Reviews:

Related manuals for TC

Brands by name

Popular brands

UniVer TC, Manual

Search results

Summary of Contents for TC

Reviews:

Related manuals for TC

Brands by name

Popular brands