UniVer TC Manual Download Page 26

Page: 26 / 80

Rev.B15

Pg. 26 di 80

How to set Profibus network address

The valid addresses for our modules are:

from

to 9

Each module has the factory address set on 02

The “Rotary Switches”, are on the upper side of the panel, under

the flap.

The address is acquired only when turned on, so to change the

address, turn off the device, set the address and turn the

device back on so it is updated.

Rotary Switch

MSD

LSD

Slave address

Most significative number

(x10)

Less significant number (x1)

Max. address

How to set the CANopen network address

Firmware version 2.0 o previous

Valid addresses: from

89 (*)

Firmware version 2.1 up tp 2.6

Valid addresses: from

99 enable the option LSS

Firmware version 2.7 forward

Valid addresses: from

to 8

9 (*)

99 enable the option LSS and/or Auto Baud Rate

Each module leaves the factory with the address set to 63.

The “Rotary Switches” are placed on the upper part of the panel, under the

flap.

The address is acquired only when it is turned on, so to change the address,

turn it off, set the address and turn the device back on so that it is

updated.

Rotary Switch

MSD

LSD

Slave address

Most significat digit (x10)

Less significant digit (x1)

Max. address

(*)

Rotary Switch

Baudrate (KB)

125

250

500

800

1000

LSS o

Autobaud

When it is turned off, set a baund, switch it on and wait for 5”, switch it off, set the desired address (< 90) and switch

it on again.

To set the address, remove the cover by unscrewing the screws, set the new address and

remember to properly close the cover by tightening the screws fully in order to ensure the IP65

protection degree.

Summary of Contents for TC

















































































Search results

Summary of Contents for TC

Reviews:

Related manuals for TC

Brands by name

Popular brands

UniVer TC, Manual

Search results

Summary of Contents for TC

Reviews:

Related manuals for TC

Brands by name

Popular brands