manualshive.com logo in svg

UniVer TC, Manual

Share
Download
UniVer TC Manual Download Page 65

 

 

 

 

Rev.B15

 

Pg. 65 di 80 

 

Parameters table 

 

Diag: 24V Main Power Loss 

Enables or disables the generation of the diagnostics in case of a power 

failure for the outputs (VA24). 

Diag: Module fail 

Enables or disables the generation of the diagnostics in case of module 

failure. 

Diag: Output fail 

Enables or disables the generation of the diagnostics in case of 

overload or short circuit of the outputs.  

Diag: High Noise level 

Enables or disables the generation of the diagnostics in case of 

detection of a high level of noise. 

Diag: 24V Input power loss 

Enables or disables the generation of the diagnostics in case of a power 

failure on the input modules. 

Fast Input response time 

Slow: input filter for very noisy environment (> 50mS). 

Fast: Maximum sampling frequency of the inputs (< 50mS). 

The time depends on the number of inputs and outputs of the system. 

Default Slow. 

Mode Manifold First 

If True, the integrated manifold will use the first 3 bytes of the 

assigned address. 

If False, the integrated manifold will use the last 3 bytes of the 

assigned address. 

Turn off output on Fail 

Select the desired behaviour in case of master CPU ALT or loss of 

communication. 

Able if you want to turn off all outputs automatically. 

Disable if you want to leave all the outputs in the last state. (in this 

case pay attention to the dangerous conditions that may be generated 

in the system). 

Default “Able” 

Diag: Other Module info 

If Able a diagnostics will be generated for each sub module. 

Diag: Electric Clamp Fail 

Enables or disables the generation of diagnostics in case of an error 

signal from the electric clamp (FAIL output of the electric clamp). 

Diag: Clamp Command Fail 

Enables or disables the generation of diagnostics in case of overload or 

short circuit of one or more control outputs of the electric clamp.  

Clamp Lag time 

Indicate the lag time between the command of an electric clamp and 

the next one (multiplicative coefficient of 5ms). 

Default 30 = 150mS. 

Clamp Actived at the same 

Time 

Indicates the number of clamps that can be activated at the same time 

(1…8). 

Default 8. 

Keep output on Safe OP 

Select the desired behaviour in case of module SAFE OP status. 

DisAble if you want to automatically turn off all the outputs. 

Able if you want to leave all the outputs in the latest status. 

(in this case pay attention to the dangerous conditions that may be 

generated in the system). 

Default “DisAble”. 

Note: if not configured, all the diagnostics functions are enabled (once written they keep the latest configured value).

 

 

The procedure for modifying the configuration parameters depends on the master software used.  

On the next page you can see an example of the menu that appears in the “TwinCAT” software by Beckhoff.  

 

 

 

Summary of Contents for TC

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands