UniVer TC Manual Download Page 21

Page: 21 / 80

Rev.B15

Pg. 21 di 80

Connection to the Profibus fieldbus network

Profibus cable specifications



Connector for fieldbus

TZ-M4M12-B

to be

connected to

BUS OUTPUT

Connector for filedbus

TZ-F4M12-B

to be

connected to

BUS INPUT

As per “Interconnection Technology Version 1.4” of January 2007 published by the

PNO, the shield of the shielded cable must be connected to connector metal case as

indicated above, and not to the pin 5 of the same.

Profibus network termination

Description

Features

Impendence

100…130 Ohm

Capacity

< 30pF/m

Resistance

< 110 Ohm/Km

Diameter

< 0,53mm

Section

> 0,22mm²

Termination TZ-M5M12-BT is to be

connected to the

BUS OUTPUT

connector.

A Profibus network must be terminated at each end of it. The master and
the last device on the network must be terminated in order to eliminate
reflections, even if only 2 nodes are used.

Termination specifications:

•

2 x 390 Ohm

•

220 Ohm

•

1% Metall film

•

¼ Watt

Summary of Contents for TC

















































































Search results

Summary of Contents for TC

Reviews:

Related manuals for TC

Brands by name

Popular brands

UniVer TC, Manual

Search results

Summary of Contents for TC

Reviews:

Related manuals for TC

Brands by name

Popular brands