UniVer TC Manual Download Page 42

Page: 42 / 80

Rev.B15

Pg. 42 di 80

Status and Diagnostics - EtherNet/IP LED

LED

Color

Status

Meaning

ON/Diag

No error.

Flashing

Error, see error codes table for further details.

Flashing

Fatal error, see error codes table for further details..

Run/Rdy

Operative system completely loaded and ready.

Error during loading of operative system or configuration

Flashing

Boot loader mode active (6 Blink No 2

Stage Loader Loaded).

Flashing

Operating system missing (2

Stage Loader Loaded).

Working (the device is correctly working)

Flashing

Standby (the device is not configurated)

Serious failure (the device has identified a non-recoverable error).

Flashing

Minor failure (the device has identified a recoverable error).

Off

Missing power supply (VLS24).

Device connected.

Flashing

No connection.

(One IP address is configurated, but there is no CIP connection).

Double IP address.

Flashing

Connection Timeout.

Off

No configurated IP address.

OUT

SUPPLY

Power supply on (24VA).

(Manifold and output power supply).

Off

No power supply (24VA).

(Manifold and output power supply).

LINK 1

Ethernet connection on channel 1.

Off

No Ethernet connection on channel 1.

LINK 2

Ethernet connection on channel 2.

Off

No Ethernet connection on channel 2.

ACT 1

Flashing

Message Transmission/Receipt on channel 1..

Off

No Message Transmission/Receipt on channel 1.

ACT 2

Flashing

Message Transmission/Receipt on channel 2.

Off

No Message Transmission/Receipt on channel 2.

Summary of Contents for TC

















































































Search results

Summary of Contents for TC

Reviews:

Brands by name

Popular brands

UniVer TC, Manual

Search results

Summary of Contents for TC

Reviews:

Brands by name

Popular brands