UniVer TC Manual Download Page 55 | Manualshive

Page: 55 / 80

background image

Rev.B15

Pg. 55 di 80

Now configure the number of bytes for the inputs and the number of bytes for the output of the used device.

(in the example we have a TCxEN and only 3 bytes for the output will be assigned).

The procedure may be slightly different in different software, however the operative sequence must be generally the

following:

1)

Set the IP address (not necessary if the DHCP is activated) and the other options by using the BootP software

or the Ethernet/IP Device Configurator.

2)

Set the device EDS file in the master.

3)

Scan the network or insert the device by selecting it from the list and put it into the window with the master.

4)

Configure the number of bytes for inputs and outputs.

5)

Configure the options of the module if necessary.

«
...
53
54
55
56
57
...
»

Summary of Contents for TC

















































































Reviews:

No comments

Related manuals for TC

Brand: Balboa Instruments Pages: 10

Brand: Quantum Data Pages: 36

Brand: Panasonic Pages: 16

Brand: Samsung Pages: 32

Brand: GBD Pages: 68

vlt soft starter mcd 500

Brand: Danfoss Pages: 95

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 33

Brand: Danfoss Pages: 59

Brand: Danfoss Pages: 16

VLT AQUA Drive FC 200

Brand: Danfoss Pages: 91

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 100

Brand: Danfoss Pages: 82

Brand: Danfoss Pages: 18

Brand: Danfoss Pages: 12

OPTYMA Plus OP-LPQM

Brand: Danfoss Pages: 8

Brand: ICP DAS USA Pages: 166

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands