Unipulse UPM100 Operation Manual Download Page 16

Page: 16 / 89

Outline

Chapter

UTM

Ⅱ

connection connector

UTM

Ⅱ

is connected using the dedicated cable.

* Refer to P.11 "2-4.Connecting the UTM

Ⅱ

External I/O connector

Connect the external I/O signal.

* Refer to P.12 "2-5.Connecting external I/O".

Thermocouple connector

Connect the K type thermocouple. Two sets can be connected.

* Refer to P.14 "2-6.Connecting the thermocouple".

RS-232C connector

RS-232C connector for reading the indicated value and status of the UPM100, and writing the
setting value to the UPM100.

* Refer to P.15 "2-7.RS-232C interface connection".

Protective grounding terminal

Be sure to ground a protective grounding terminal to prevent electric shock accidents.

* Refer to P.9 "2-2.Connecting protective grounding terminals".

Summary of Contents for UPM100


























































































Search results

Summary of Contents for UPM100

Reviews:

Related manuals for UPM100

Brands by name

Popular brands

Unipulse UPM100, Operation Manual

Search results

Summary of Contents for UPM100

Reviews:

Related manuals for UPM100

Brands by name

Popular brands