Unipulse UPM100 Operation Manual Download Page 27

Page: 27 / 89

Setting Procedures

Chapter

3-2.

Key operation

<<Setting procedures>>

Setting mode

Choose a digit to set.

Change the setting value.

Confirms the setting value and moves on to the

Cancels the change to the setting value and moves on to the

The FNC lamp lights on.

Setting selection,

Returns to the indicated value

FUNC

cal

SYSTEM

MEM

ESC

VOL

OUT

ALARM

RST/.

"cal" representing

▽

△

Press the key to add a minus sign to

ENT

ESC

"SYS" representing

"mEm"

"voL" representing

"ALSEt"

▽

* The selected setting value will flash.

REC

USB

"uSb" representing

capacity
setting mode
is displayed.

system
setting mode
is displayed.

representing record
setting mode
is displayed.

voltage output
setting mode
is displayed.

representing
alarm setting
mode is
displayed.

USB data
transfer mode
is displayed.

setting value entry

the setting value.

next setting item.

next setting item or returns to the indicated value display.

selection

☆

－

When there is no key operation for over one minute in the setting items (exclud-
ing the self-test), the setting is aborted and the indicated value display will be
shown again.
In this case, the setting value is not recorded.

Key point

Summary of Contents for UPM100


























































































Search results

Summary of Contents for UPM100

Reviews:

Related manuals for UPM100

Brands by name

Popular brands

Unipulse UPM100, Operation Manual

Search results

Summary of Contents for UPM100

Reviews:

Related manuals for UPM100

Brands by name

Popular brands