Unipulse UPM100 Operation Manual Download Page 15

Page: 15 / 89

Outline

Chapter

Alarm reset
Resets ALARM status of external output. ALARM lamp lights off.

Push the

keys and select "ESC" "CLr-Pt" "CLr-AL".

* CLr-Pt: Clear point data

CLr-AL: Clear alarm record data

The

key functions as a decimal point (.) key when entering data.

Press the

keys and configure the alarm condition.

Setting for alarm detection items

Target: Each interphase voltage, average interphase voltage, each phase current,

average phase current, effective power, reactive power, apparent power.

Alarm detection level

Threshold of item settings of alarm detection

Confirms data when setting screen is displayed.

Rear panel

Power supply input connector

Connect the included dedicated AC adapter for the UPM100.
Input power is AC100 to 240V (-15%, +10%), free power supply. Frequency is 50/60Hz.

* Refer to P.9 "2-1.Connecting the power input connector".

Input terminal for measuring electric power

Connect the electric wire to measure.

* Refer to P.10 "2-3.Connecting the measurement circuit of electric power".

ALARM

RST/.

△

▽

ALARM

RST/.

FUNC

ALARM

RST/.

ENT

External I/O connector

Input terminal for measuring electric power

Power supply input

RS-232C connector

UTM

Ⅱ

connector

Thermocouple connector

Protective grounding

connector

terminal

Summary of Contents for UPM100


























































































Search results

Summary of Contents for UPM100

Reviews:

Related manuals for UPM100

Brands by name

Popular brands

Unipulse UPM100, Operation Manual

Search results

Summary of Contents for UPM100

Reviews:

Related manuals for UPM100

Brands by name

Popular brands