manualshive.com logo in svg

UNIBLOC PD600, Operation & Service Manual, Page: 6 / 55

Share
Download
UNIBLOC PD600 Operation & Service Manual Download Page 6

6  UNIBLOC-PD Operation & Service Manual: PD600-677

1.2.2 Noise Emission

Under certain operating conditions, pumps and/or drives and/or the systems within which they are installed can pro

-

duce sound pressure levels that exceed 80dB. In such cases ear protection should be used. 

1.2.3 Marking – Standard

Standard marking is machined on the side of pumps’ bearing housing. Pump size is machined on rotor housing next 

to the ports. See figure 1.4 for details.

2.0 Safety

2.1 General

This information must be read carefully before installation, operation or servicing.  The safety instruction must always 

be available for the pump operator.  The following symbols are used. 

WARNING: Indicates instructions that can affect personal safety if not followed. 

WARNING: Indicates electrical voltage instructions that can affect personal safety if not fol

-

lowed.  

ATTENTION: Indicates instructions to be considered for safe operation and to protect the 

pump and pump unit. 

2.2 Safety Instructions

Incorrect installation, operation or maintenance of the equipment can cause serious personal injury and/or damage to 

the equipment and will invalidate the warranty.  Make sure the pipes are well supported as the pump is not meant to 
serve this purpose. Keep in mind that pipes filled with liquid are very heavy. See fig. 2.1 for recommended pipe layout.

WRONG

RIGHT

PUMP SIZE

SERIAL NUMBER

fig. 1.4  

   

   

fig. 2.1  

Summary of Contents for PD600
























































Reviews:

No comments